An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen. Once the temperature increases above freezing, the water supply will resume.

How do I fix error code 1E?

Disconnect the strainer, clean and rinse it, as it may become clogged. Check the condition of the hose. It is possible that it is pinched, clogged, bent or twisted. Unplug the washing machine: unplug the cord and plug it into the power outlet after 5-10 minutes to reset error code 1E.

How do I fix E1 error on washing machine?

  1. Check that the water faucets are not closed.
  2. Check that the water pressure in the house is over 20 kPa.
  3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
  4. Check that the drain hose is not below 27½” (700 mm) from the floor.

How do you fix IE error on LG top load washer?

Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.

How do I fix the error code on my LG washer?

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

What does UC mean in Samsung washing machine?

Error CodeCauseUCExcessuve Fluctuation In The Supply Voltage (voltage has fluctuated outside 176-286vAC)UE, E4Unbalanced Error (the washing load in the drum is unbalanced i.e. clothes may have got trapped inside a large towel and resting on one side of the drum)

How do I fix 1E error on Samsung washing machine?

  1. Do a hard power reset. You need to unplug your Samsung washing machine for about 5 minutes as this will normally reset most of the electronic glitches or any other issues with software that may be present. …
  2. Ensure proper wire connection. …
  3. Replace the pressure switch.

How do I force drain my LG washer?

If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water.

How do I clear the IE code on my LG dishwasher?

Check the water supply hose Check the filter on the water supply hose. Unplug the appliance and turn off the water tap or water valve. Unscrew the water supply hose. Remove the seal and plastic filter with a pair of small pliers or scissors.

What is PE error in LG washing machine?

The PE error code indicates that the water level sensor is malfunctional. To fix this: Unplug the washer for 10 seconds. Plug the washer back in, and restart the cycle again.

Article first time published on

How do I fix the error E1 on my Haier washing machine?

Question: Error Code-control panel display “E1” Drain error, water can not drain fully within the required drain time (controlled by PCB software ). Solution: Remove and clean the pump filter. Check drain hose for blockage and proper installation.

What is E4 error in washing machine?

When the washing machine shows error E4, the washing machine doesn’t get water or too little water to run the program. … If it’s open, check the water supply. The inlet hose may be clogged or kinked. If this is the case, remove the kink.

What is E2 error in washing machine?

The E2 error in Samsung washing machines informs the user about water draining problems. For some reasons, the device can’t drain the waste of water. Besides, it can report about unhurried discharge. So waiting time for draining is exceeded.

What does IE error mean on LG washer?

An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen. Once the temperature increases above freezing, the water supply will resume.

Is there a reset button on my LG washer?

Washer Needs Hard Reset If your LG washing machine won’t start, try doing a hard reset on the unit. To perform a reset, start by unplugging your washer. Then, press and hold the power button for 5 seconds. Do the same with the play button.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

What is Le error in Samsung washing machine?

Samsung washing machine error code LE means the washer has tried to fill but has not reached the proper water level. Check the water supply valves are fully opened.

What does 1E mean on Samsung dishwasher?

When a Clogged Filter Error (1E) occurs, it means the fine filter at the bottom of the dishwasher is dirty. You will need to clean the filter to clear this notification. For better washing performance, clean the filter at least once a month.

How do I fix 5E error on Samsung washing machine?

  1. Turn off the washer and check that it is level. …
  2. Inspect the drain hose. …
  3. Clean the pump filter (for front load only*). …
  4. Turn the washer back on and start a cycle. …
  5. Request service.

What are washing machine error codes?

AskoFailure CodeCondition“dE” – Lid open errorLid is open during wash cycle.“UE” – Unbalance switch errorUnbalanced load is sensed three times during a spin operation.“OE” – Water overflow errorWater supply does not stop after sensing an overflow condition.

How long does Sud error last?

If you have noticed a SUD code during a washing cycle, it means the suds have exceeded the drum’s usual level. More specifically, this error means that the washing machine is reducing foaming. It has just stopped for 5-10 minutes to allow the suds to dissipate and the washing cycle to go on.

Why is my dishwasher saying IE?

The lg dishwasher error code e1 is an indication that the running pump is not getting enough back pressure from the dishwasher while operating. Or for some LG dishwasher models also, E1 error code means, there is water leaking into the dishwasher drain pan. … A drain hose leak is the most likely cause of this error.

Why is my LG dishwasher flashing IE?

An IE error code signifies that the washing machine is filling with water slowly or not at all. This can occur when water supply taps are not fully open or the water pressure to the tap or house is too low. This time of year it can also be a partially frozen water pipe.

How do I fix E1 error on LG dishwasher?

Water leakage from under the dishwasher door is the most common problem. Hopefully, it is easily removable like the E1 error code. To do this, open the door and manually tear off the old sealing gum along the perimeter of the appliance. Then, take a new sealing gum, suitable for a specific model of the LG dishwasher.

Why does my washer not drain?

There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.

Why is my LG washer not draining completely?

Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.

How do you manually drain a washing machine?

  1. Step 1: Turn off the power and lay down towels.
  2. Step 2: Locate the drain hose at the back of the washing machine.
  3. Step 3: Drain the water.
  4. Step 1: Turn off the power and lay down towels.
  5. Step 2: Locate the drain hose.
  6. Step 3: Drain the water.
  7. Step 4: Scrub the filter.

How do you clear the CL code on a LG washing machine?

TO TURN OFF CL CODE ON NEWER LG FRONT LOAD WASHERS: To TURN OFF CHILD LOCK on your LG washer, press and hold the CHILD LOCK button for 3 to 5 seconds. The washer should now have CHILD LOCK mode DISABLED and all buttons will function properly.

What is PE in Whirlpool washing machine?

PE. Of all the Whirlpool washing machine error codes, PE is one that may require a professional repair. This code usually indicates a problem with the pressure level sensor. This sensor monitors how much water is in the machine, also telling the control board if it’s been filled or emptied.

How do you fix a Haier washing machine that will not drain?

If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.

How do I fix error E3 on my Haier washing machine?

The screen displays ”E3” with alarm. Reason 1: Is the laundry put unevenly in the washing machine? Solution: Redistribute the laundry evenly. Close the top lid and press the START/PAUSE button.